When installed properly, the locator will not screw down tightly, but will rotate freely. Page 64 Controls and features Cargo cover if equipped Your vehicle is equipped with a cargo area shade that covers the luggage compartment of your vehicle.
To install the shade: 1. Position the shade in mounting brackets as shown. The tongue faces the rear of the vehicle. Page 65 Controls and features 1. Remove the shade from the vehicle and extend it with the smooth grain facing you. Wrap the vinyl around the roller tube twice. Tuck the edges of the vinyl inside the end cap with each wrap. Page 67 Controls and features Identifying an armed anti-theft system When the system is armed, the warning light will illuminate for 30 seconds.
After 30 seconds, the light will flash. If the system is armed with the doors open, the warning light will stay illuminated until all the doors are closed and then illuminate for 30 seconds and begin flashing. The remote entry system features only operate with the ignition in the Off position.
It also arms and disarms the anti-theft system if equipped. To confirm all doors are closed and locked, press the LOCK control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash. If the horn chirps twice, a door is still ajar and the anti-theft system will not arm. Page 72 Controls and features 5. Press the door power unlock switch three times. Turn the ignition key back to ON within 30 seconds of step two. The horn should chirp once.
If not, wait 30 seconds and repeat steps one through six. To replace the batteries: 1. Twist a thin coin between the two halves of the transmitter. The computer code that operates the keyless system is located on your owners wallet card found in Page 75 Controls and features The system has shut down if the keypad light is out. If the keyless entry system does not work, use the key or remote entry transmitter s.
To unlock the driver door, enter one of the two codes. After pressing the fifth number, the driver door unlocks. Page 76 Controls and features 1. Enter the original permanent code. Wait six seconds. For maximum security, do not set a code that presents the numbers in sequential order or uses the same button five times. The autolock feature can be disabled or reenabled by using the keyless entry system Rear seat four-way head restraints if equipped Push or pull the head restraint to the desired position.
Page 79 Seating and safety restraints SEATING Adjusting bench seating Folding rear seats if equipped If your vehicle is equipped with a built-in child safety seat, the seatback cannot be folded down unless the built-in child seat is fully stowed. Press the lower release control downward to unlatch the seatback. Pull up to recline the seat.
Adjusting the power front seats if equipped Pull up to recline the seat. Page 81 Seating and safety restraints Press to tilt the front of the seat up or down. Press in the desired direction for seat adjust or to move the seat forward or back. In most states and Canada, the law requires the use of safety belts. Always drive and ride with your seatback upright and the lap belt snug and low across Page 84 Seating and safety restraints Using safety restraints properly Combination lap and shoulder belts Insert the tongue into the slot in the buckle fasten.
Push the red release button and remove the tongue from the slot to unfasten. The outboard safety restraints in the vehicle are combination lap and shoulder belts.
Page 85 Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically prelocked; however, the belt will retract to remove any slack in the shoulder belt.
The automatic locking mode is not available on the driver safety belt. Page 86 Seating and safety restraints Canceling automatic locking mode Disconnect the combination lap and shoulder belt and allow it to completely retract. This will cancel the automatic locking mode and activate the vehicle sensitive emergency locking mode.
Front seat safety belt height adjustment Adjust the height of the shoulder belt so that the belt rests across Page 87 Seating and safety restraints Using lap belts Adjusting the lap belt A lap belt is located in the center of the rear seat. Page 88 Seating and safety restraints Conditions of operation If.. Page 89 Seating and safety restraints Safety belt extension assembly The safety belt may be too short even when it is fully extended.
Approximately 20 cm 8 inches may be added to the length of the belt with a safety belt extension part C See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide. Page 91 Seating and safety restraints Rear-facing child seats or infant carriers should never be placed in the front seats. How does the air bag supplemental restraint system SRS work?
Page 92 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant.
This may consist of cornstarch, talcum powder to lubricate the bag or sodium compounds e. Page 93 Seating and safety restraints The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system readiness including the impact sensors , the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
Page 94 Seating and safety restraints Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Page 95 Seating and safety restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Page 96 Seating and safety restraints Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Children and safety belts Children who are too large for child safety seats as specified by your child safety seat manufacturer should always wear safety belts.
Page 97 Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is Page 98 Seating and safety restraints anchorage.
For more information on top tether straps see Attaching safety seats with tether straps in this chapter. Page 99 Seating and safety restraints seat, move the seat as far back as possible. Rear-facing child seats or infant carriers should never be placed in the front seats.
Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. Page Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page Tether anchor hardware kits part number D74 , including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. Only use the tether attachment hole locations shown in the illustrations. Page Seating and safety restraints Built-in child seat if equipped The rear seat may be equipped with a built-in child safety seat.
This child seat conforms to all federal and Canadian motor vehicle safety standards. Read the labels located on the child seat cushion and shoulder belt for more information on the built-in child seat. Page Seating and safety restraints The second row seatback must be fully locked before operating the child restraint system. Check the position of the seatback release lever.
Never use the Built-In Child Seat as a booster cushion with the adult safety belts. Page Seating and safety restraints 3. Lower the child seat cushion. Unfold the cushion protector flap onto adult seat cushion.
If connected, disconnect the chest clip and buckles. Page Seating and safety restraints If both tongues do not latch in the buckle, do not use the child seat. See your dealer for repairs. Page Seating and safety restraints Activating the automatic locking mode ALR on the built-in child safety seat 1.
Fully extend the right shoulder belt. Deactivating the automatic locking mode ALR on the built-in child safety seat 1. Page Inspecting the built-in child safety seat after a collision Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Page Seating and safety restraints All built-in child restraints, including seats, buckles, retractors, seat latches, interlocks, and attaching hardware should be inspected by a qualified dealer technician after any collision.
When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Page Starting If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Page Starting Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle Page Starting standard requirements regulating the impulse electrical field strength of radio noise.
When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the vehicle in this chapter. If a light fails to illuminate, have the vehicle serviced.
Page Starting accelerator and start the engine while holding the accelerator down. Release accelerator when engine starts. After idling for a few seconds, apply the brake and release the parking brake. Using the engine block heater if equipped An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the Anti-lock brake system ABS if equipped The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency.
The front wheels are prevented from locking even when the brakes are firmly applied. Page Driving Parking brakes To engage the parking brake: To disengage the parking brake: Always set the parking brake fully and make sure that the gearshift is securely latched in P Park automatic transmission or in 1 First manual transmission. Extended use of other than matching size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. Page Driving based on driver and road inputs to optimize ride.
The combination of firm dampening and height change also provides maximum suspension feedback for improved off-road safety and performance. The vehicle will drop to its lowest position when the ignition is turned to the Off position to provide easy entry and exit to of the vehicle. The switch does not control or change the performance of the All Wheel Drive system. The switch should be placed in the Normal position for all on road and most dirt, gravel or snow covered Page Roadside Emergencies Driving the brake pedal is depressed.
If you cannot move the gearshift lever from P Park with the brake pedal depressed: 1. Apply the parking brake. Turn the ignition key to Lock, then remove the key.
Insert the key and turn the ignition off. Page Driving towing a trailer or heavy loads through heavy terrain. To return to Overdrive mode, press the transmission control switch. When starting your vehicle, the transmission will automatically return to normal Overdrive mode. Page Driving D Drive Not shown on the display. Activate by pressing the transmission control switch.
Transmission operates in gears one through four. D Drive provides more engine braking than Overdrive and is useful when towing a trailer or heavy loads through heavy terrain. Page Driving Driving a manual transmission if equipped Using the clutch Vehicles equipped with a manual transmission have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission: 1. Page Driving Parking 1.
Apply the brake and shift into N Neutral. Engage the parking brake. Shift into 1 First. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. This is s special lockout feature that protects you from accidently shifting into R Reverse when you downshift from 5 Overdrive.
Page Driving Driving off-road with 4WD Your vehicle is specially equipped for driving on snow, sand, mud or other rough terrain and has operating characteristics that differ from those of other conventional vehicles. When using 4WD, maintain steering wheel control at all times, especially in rough terrain. Page Driving accelerator slowly and avoid spinning the wheels. Driving through mud and water After driving through mud, clean off residue stuck to rotating driveshafts and tires.
Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components. Page Driving Driving Through Water Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Page Driving When descending a steep hill, avoid sudden braking. Rapid pumping of the brake pedal will help slow the vehicle and still maintain steering control.
When speed control is on and you are driving uphill, your vehicle speed may drop considerably, especially if you are carrying a heavy load. Page Driving Allow more stopping distance and drive slower than usual. Consider using one of the lower gears. If either light flashes, see your dealer or qualified service technician.
Page Driving Utility and four-wheel drive vehicles are NOT designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles.
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. To achieve your objectives, customers are given 3 options. Visit our website and select manual which is designed for Explorer model years , , , , , and We are recognized worldwide for our quality pdf manuals.
Instead of purchasing cheap rated service manual based on a few hundred pages, visit our website and select reasonably priced manuals that have covered more than pages. Thousands of pages for second generation confirm that each and every repairing or maintenance job is discussed in detail.
As second generation factory manual was designed almost fifteen years ago therefore many customers believe that latest features are not accessible. It is our job to update all our PDF manuals on routine basis and introduce latest features concerning bookmark type, wiring diagrams , visual aid and illustrations. Ford Explorer Second generation — manual is based on graspable method.
We'll get you the repair information you need, every time, or your money back. Manufacturer: Ford. Model: Explorer. Production Year: Step by Step Instructions. Comprehensive Diagrams. Diagnostic Procedures. Wiring Diagrams. Here is what you'll get. Step-by-step factory recommended repair instructions. Unlimited access to personal support reps who are always available to assist you.
0コメント